View LP133X8-A2M1_7780158.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LP133X8-A2M1 liquid crystal display product specification ver 1.0 aug. 01. 2001 page 1 1 1 1 / 24 24 24 24 specification for approval ( ) preliminary specification ( ? ? ? ? ) final specification title 13.3? xga tft lcd supplier lg.philips lcd co., ltd. buyer asustek model LP133X8-A2M1 model safety application model lp133x8 * when you obtain standard approval , please use the above model name without suffix . signature / date approved by y. k.hwang / s.manager date / reviewed by s.m.lee / s.manager s.k.ahn / manager / prepared by y.c. jung / engineer b. d. jun / engineer please return 1 copy for your confirmation with your signature and comments. product engineering dept. lg.philips lcd co., ltd. www.datasheet.net/ datasheet pdf - http://www..co.kr/
LP133X8-A2M1 liquid crystal display product specification ver 1.0 aug. 01. 2001 page 2 2 2 2 / 24 24 24 24 contents no. item page - cover 1 - contents 2 - record of revisions 3 1 general description 4 2 absolute maximum ratings 5 3 electrical specifications 3-1 electrical characteristics 6 3-2 interface connections 7 3-3 signal timing specifications 9 3-4 signal timing waveforms 10 3-5 color input data reference 11 3-6 power sequence 12 4 optical specifications 13 5 mechanical characteristics 16 6 reliability 20 7 international standards 7-1 safety 21 7-2 emc 21 8 packing 8-1 designation of lot mark 22 8-2 packing form 22 9 precautions 23 www.datasheet.net/ datasheet pdf - http://www..co.kr/
LP133X8-A2M1 liquid crystal display product specification ver 1.0 aug. 01. 2001 page 3 3 3 3 / 24 24 24 24 records of revisions version no date page description 1.0 aug 01, 2001 - final www.datasheet.net/ datasheet pdf - http://www..co.kr/
LP133X8-A2M1 liquid crystal display product specification ver 1.0 aug. 01. 2001 page 4 4 4 4 / 24 24 24 24 1. general description the LP133X8-A2M1 is a color active matrix liquid crystal display with an integral cold cathode fluorescent lamp(ccfl) backlight system. the matrix employs a-si thin film transistor as the active element. it is a transmissive type display operating in the normally white mode. this tft-lcd has a 13.3 inches diagonally measured active display area with xga resolution(768 vertical by 1024 horizontal pixel array). each pixel is divided into red, green and blue sub-pixels or dots which are arranged in vertical stripes. gray scale or the brightness of the sub-pixel color is determined with a 6-bit gray scale signal for each dot, thus, presenting a palette of more than 262,144 colors. the LP133X8-A2M1 has been designed to apply the interface method that enables low power, high speed, low emi. flat link must be used as a lvds(low voltage differential signaling) chip. the LP133X8-A2M1 is intended to support applications where thin thickness, low power are critical factors and graphic displays are important. in combination with the vertical arrangement of the sub-pixels, the LP133X8-A2M1 characteristics provide an excellent flat panel display for office automation products such as notebook pc. general features active screen size 13.3 inches(33.78cm) diagonal outline dimensions 284(h) x 214.5(v) x 5.2(d) mm (typ.) pixel pitch 0.264 mm x 0.264 mm pixel format 1024 horiz. by 768 vert. pixels rgb stripe arrangement color depth 6-bit, 262,144 colors luminance,white 150 cd/m 2 (typ.) power consumption total 4.7 watt(typ.) weight 390g (typ.) display operating mode transmissive mode, normally white surface treatments hard coating (3h), anti-glare treatment of the front polarizer cn1: df19kr-20p-1h or equivalent , cn2: bhsr-02vs-1(jst) column driver circuit row driver circuit tft-lcd (1024 x 768) timing control block power block flatlink interface backlight ass?y cn1 cn 2 www.datasheet.net/ datasheet pdf - http://www..co.kr/
LP133X8-A2M1 liquid crystal display product specification ver 1.0 aug. 01. 2001 page 5 5 5 5 / 24 24 24 24 2. absolute maximum ratings the following are maximum values which, if exceeded, may cause faulty operation or damage to the unit. table 1 absolute maximum ratings values parameter symbol min. max. units notes power input voltage operating temperature operating tempe. for panel storage temperature operating ambient humidity storage humidity v cc t op - t st h op h st -0.3 0 0 -20 10 10 4.0 50 60 60 90 90 vdc c c c %rh %rh at 25 5 c 1 2 1 1 1 note: 1. temperature and relative humidity range are shown in the figure below. wet bulb temperature should be 39 c max, and no condensation of water. 2. the surface temperature caused by self heat radiation of cell itself is specified on this item. www.datasheet.net/ datasheet pdf - http://www..co.kr/
LP133X8-A2M1 liquid crystal display product specification ver 1.0 aug. 01. 2001 page 6 6 6 6 / 24 24 24 24 3. electrical specifications 3-1. electrical characteristics the LP133X8-A2M1 requires two power inputs. one is employed to power the lcd electronics and to drive the tft array and liquid crystal. the second input which powers the ccfl, is typically generated by an inverter. the inverter is an external unit to the lcd. table 2 electrical characteristics: parameter symbol values units notes min. typ. max. module power supply input voltage power supply input current differential impedance power consumption rush current v cc i cc z m p c i rush 3.0 - 90 - - 3.3 270 100 0.9 1.5 3.6 390 110 1.2 1.8 vdc ma ohm w a 1 2 1 3 lamp operating voltage operating current established starting voltage at 25 c 0 c discharge stabilization time operating frequency power consumption life time v bl i bl ts f bl p bl - 3.0 - - 40 - 10,000 620 6.0 - - 60 3.8 682 6.5 1050 1260 3 80 4.2 - v rms ma v rms v rms min khz watts hours 4 5 5 7 6 8 9 notes: the design of the inverter must have specifications for the lamp in lcd assembly. the performance of the lamp in lcm,for example life time or brightness,is extremely influenced by the characteristics of the dc-ac inverter.so all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter. when you design or order the inverter,please make sure unwanted lighting caused by the mismatch of the lamp and the inverter(no lighting,flicker,etc) never occurs.when you confirm it,the lcd assembly should be operated in the same condition as installed in your instrument. 1. the specified current and power consumption are under the vcc = 3.3v , 25 c, fv = 60hz condition whereas 64 gray pattern is displayed. 2. this impedance value is needed to proper display and measured form lvds tx to the mating connector. 3. the duration of rush current is about 20ms. 4. the variance of the voltage is 10%.(at typical current) 5. the voltage above v s should be applied to the lamps for more than 1second for start-up. otherwise,the lamps may not be turned on. 6. the output of the inverter must have symmetrical(negative and positive) voltage waveform and symmetrical current waveform.(unsymmetrical ratio is less than 10%) please do not use the inverter which has unsymmetrical voltage and unsymmetrical current and spike wave. lamp frequency may produce interference with horizontal synchronous frequency and as a result this may cause beat on the display. therefore lamp frequency shall be as away as possible from the horizontal synchronous frequency and from its harmonics in order to prevent interference. 7. let?s define the brightness of the lamp after being lighted for 5 minutes as 100%. t s is the time required for the brightness of the center of the lamp to be not less than 95%. 8. the lamp power consumption shown above does not include loss of external inverter. (at typical current) www.datasheet.net/ datasheet pdf - http://www..co.kr/
LP133X8-A2M1 liquid crystal display product specification ver 1.0 aug. 01. 2001 page 7 7 7 7 / 24 24 24 24 9. the life time is determined as the time at which brightness of lamp is 50% compared to that of initial value at the typical lamp current on condition of continuous operating at 25 2 c . notes:do not attach a conduction tape to lamp connection wire if the lamp wire attach to a conducting tape, tft-lcd module has a low luminance and the inverter has abnormal action. because leakage current is occurred between lamp wire and conducting tape. 3-2. interface connections interface chip must be used flatlink, part no. sn75lvds84(transmitter) made by texas instrument inc. or equivalent.. this lcd employs two interface connections, a 20 pin connector is used for the module electronics and the other connector is used for the integral backlight system. the electronics interface connector is a model df19kr-20p-1h manufactured by hirose or equivalent. the pin configuration for the connector is shown in the table below. table 3 module connector pin configuration (lvds) pin symbol description notes 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 vcc vcc gnd gnd a1m a1p gnd a2m a2p gnd a3m a3p gnd clkm clkp gnd nc nc gnd gnd power (3.3v) power (3.3v) ground ground differential signal differential signal ground differential signal differential signal ground differential signal differential signal ground differential signal differential signal ground no connection no connection ground ground 1. interface chips 1.1 lcd : sn75lvds88b(lcd controller) including lvds receiver 1.2 system : sn75lvds84 or equivalent * pin to pin compatible with thine lvds 2. connector 2.1 lcd: df19kr-20p-1h,hirose or equivalent 2.2 mating: df19g-20s-1c or equivalent. 2.3 connector pin arrangement [ lcd module rear view ] the backlight interface connector is a model bhsr-02vs-1, manufactured by jst. the mating connector part number is sm02b-bhss-1 or equivalent. the pin configuration for the connector is shown in the table below. table 4 backlight connector pin configuration pin symbol description notes 1 2 hv lv power supply for lamp (high voltage side) power supply for lamp (low voltage side) 1 1 notes: 1. the high voltage side terminal is colored pink. the low voltage side terminal is white. 1 1 1 1 20 20 20 20 www.datasheet.net/ datasheet pdf - http://www..co.kr/
LP133X8-A2M1 liquid crystal display product specification ver 1.0 aug. 01. 2001 page 8 8 8 8 / 24 24 24 24 table 5 required signal assignment for flatlink transmitter pin # pin name require signals pin # pin name require signals 1 d4 r4 48 d3 r3 2 vcc vcc 47 d2 r2 3 d5 r5 46 gnd gnd 4 d6 g0 45 d1 r1 5 gnd gnd 44 d0 r0 6 d7 g1 43 nc nc 7 d8 g2 42 lvds gnd lvds gnd 8 vcc vcc 41 y0m a0m 9 d9 g3 40 y0p a0p 10 d10 g4 39 y1m a1m 11 gnd gnd 38 y1p a1p 12 d11 g5 37 lvds vcc lvds vcc 13 d12 b0 36 lvds gnd lvds gnd 14 nc nc 35 y2m a2m 15 d13 b1 34 y2p a2p 16 d14 b2 33 clkoutm clkm 17 gnd gnd 32 clkoutp clkp 18 d15 b3 31 lvds gnd lvds gnd 19 d16 b4 30 pllgnd pll gnd 20 d17 b5 29 pllvcc pll vcc 21 vcc vcc 28 pllgnd pll gnd 22 d18 hsync 27 shdn shdn 23 d19 vsync 26 clkin dclk 24 gnd gnd 25 d20 de(data enable) notes : refer to lvds transmitter data sheet for detail descriptions. www.datasheet.net/ datasheet pdf - http://www..co.kr/
LP133X8-A2M1 liquid crystal display product specification ver 1.0 aug. 01. 2001 page 9 9 9 9 / 24 24 24 24 3-3. signal timing specifications this is the signal timing required at the input of the lvds transmitter. all of the interface si gnal timing should be satisfied with the following specifications for it?s pr oper operation. table 6 timing table item symbol min. typ. max. unit note dclk period t clk 15.32 15.4 15.48 ns typ. 65mhz hsync period t hp 1206 1344 1364 t clk width-active t wh 8 136 240 vsync period t vp 780 806 830 t hp frequency f v - 60 - hz width-active t wv 1 - 24 t hp de h-back porch t hbp 10 - - (data h-front porch t hfp 10 - - t clk enable) v-back porch t vbp 2 - - v-front porch t vfp 1 - - t hp www.datasheet.net/ datasheet pdf - http://www..co.kr/
LP133X8-A2M1 liquid crystal display product specification ver 1.0 aug. 01. 2001 page 10 10 10 10 / 24 24 24 24 3-4. signal timing waveforms d d d dclk clk clk clk hsync, vsync, de, data hsync, vsync, de, data hsync, vsync, de, data hsync, vsync, de, data t t t t clk clk clk clk 0.5v 0.5v 0.5v 0.5v cc cc cc cc h h h hs s s sync ync ync ync de(data enable) de(data enable) de(data enable) de(data enable) vsync vsync vsync vsync de(data en de(data en de(data en de(data enable) able) able) able) 0.7vcc 0.7vcc 0.7vcc 0.7vcc 0.3vcc 0.3vcc 0.3vcc 0.3vcc t t t t wh wh wh wh t t t t hp hp hp hp t t t t hfp hfp hfp hfp t t t t hbp hbp hbp hbp t t t t vp vp vp vp t t t t wv wv wv wv t t t t vbp vbp vbp vbp t t t t vfp vfp vfp vfp www.datasheet.net/ datasheet pdf - http://www..co.kr/
LP133X8-A2M1 liquid crystal display product specification ver 1.0 aug. 01. 2001 page 11 11 11 11 / 24 24 24 24 3-5. color input data reference the brightness of each primary color(red, green and blue) is based on the 6-bit gray scale data input for the color; the higher the binary input, the brighter the color. the table below provides a reference for color versus data input. table 7 color data reference input color data color red msb lsb green msb lsb blue msb lsb r5 r4 r3 r2 r1 r0 g5 g4 g3 g2 g1 g0 b5 b4 b3 b2 b1 b0 basic colors black red(63) green(63) blue(63) cyan magenta yellow white 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 1 0 1 0 1 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 red red(00) dark red(01) red(02) red(61) red(62) red(63) bright 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 1 : 0 1 1 0 1 0 : 1 0 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 green green(00)dark green(01) green(02) green(61) green(62) green(63)bright 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 1 : 0 1 1 0 1 0 : 1 0 1 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 blue blue(00) dark blue(01) blue(02) blue(61) blue(62) blue(63) bright 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 0 0 0 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 0 : 1 1 1 0 0 1 : 0 1 1 0 1 0 : 1 0 1 www.datasheet.net/ datasheet pdf - http://www..co.kr/
LP133X8-A2M1 liquid crystal display product specification ver 1.0 aug. 01. 2001 page 12 12 12 12 / 24 24 24 24 3-6. power sequence parameter values units min. typ. max. t 1 t 2 t 3 t 4 t 5 t 6 t 7 - 0 200 200 0 - 400 - - - - - - - 10 50 - - 50 10 - ms notes: 1. please avoid floating state of interface signal at invalid period. 2. when the interface signal is invalid, be sure to pull down the power supply for lcd v cc to 0v. 3. lamp power must be turn on after power supply for lcd and interface signal are valid. interface signal, v i (lvds signal of transmitter) power for lamp power supply for lcd v cc 90% 90% 90% 90% 10% 10% 10% 10% 0v 0v 0v 0v t t t t 6 6 6 6 10% 10% 10% 10% 90% 90% 90% 90% t t t t 1 1 1 1 t t t t 2 2 2 2 t t t t 5 5 5 5 t t t t 7 7 7 7 valid data valid data valid data valid data 0v 0v 0v 0v off off off off off off off off lamp on lamp on lamp on lamp on t t t t 3 3 3 3 t t t t 4 4 4 4 www.datasheet.net/ datasheet pdf - http://www..co.kr/
LP133X8-A2M1 liquid crystal display product specification ver 1.0 aug. 01. 2001 page 13 13 13 13 / 24 24 24 24 4. optical specifications optical characteristics are determined after the unit has been ?on? and stable for approximately 30 minutes in a dark environment at 25 c. the values specified are at an approximate distance 50cm from the lcd surface at a viewing angle of and equal to 0 c. fig 1. presents additional information concerning the measurement equipment and method. fig. 1 optical characteristic measurement equipment and method table 8 optical characteristics ( ta=25 c, vcc=3.3v, f v =60hz, dclk=65mhz, i bl = 6 ma) parameter symbol values units notes min. typ. max. contrast ratio surface luminance, white luminance variation response time rise time decay time cie color coordinates red green blue white viewing angle x axis, right ( =0o) x axis, left( =180o) y axis, up( =90o) y axis, down ( =270o) gray scale cr l wh white tr tr r tr d x r y r x g y g x b y b x w y w r l u d 140 120 - - - 0.546 0.315 0.281 0.522 0.126 0.117 0.294 0.318 40 40 10 30 - 170 150 1.35 30 30 0.576 0.345 0.311 0.552 0.156 0.147 0.324 0.348 - - - - - - - 1.45 50 50 0.606 0.375 0.341 0.582 0.186 0.177 0.354 0.378 - - - - - cd/m 2 ms degree 1 2 3 4 5 6 notes: 1. contrast ratio (cr) is defined mathematically as : surface luminance with all white pixels contrast ratio = surface luminance with all black pixels 2. surface luminance is the center point across the lcd surface 50cm from the surface with all pixels displaying white. for more information see fig 2. lcd module optical stage(x,y) field = 1 prichard 880 or equivalent 500mm www.datasheet.net/ datasheet pdf - http://www..co.kr/
LP133X8-A2M1 liquid crystal display product specification ver 1.0 aug. 01. 2001 page 14 14 14 14 / 24 24 24 24 3. the variation in surface luminance, white is determined by measuring l on at each test position 1 through 5, and then dividing the maximum l on of 5 points luminance by minimum l on of 5 points luminance. for more information see fig 2. white maximum (l on1 , l on2 , ....l on5 ) minimum (l on1 , l on2 , ....l on5 ) 4. response time is the time required for the display to transition from white to black (rise time, tr r ) and from black to white (decay time, tr d ). for additional information see fig 3. 5. viewing angle is the angle at which the contrast ratio is greater than 10. the angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the lcd surface. for more information see fig 4. 6.gray scale specification. * gamma value = 2.2 gray level luminance(%) (typ.) l0 0.35 0.35 0.35 0.35 l7 0. 0. 0. 0.90 90 90 90 l15 3.7 3.7 3.7 3.71 1 1 1 l23 9.49 9.49 9.49 9.49 l31 20.6 20.6 20.6 20.6 l39 35.4 35.4 35.4 35.4 l47 54.5 54.5 54.5 54.5 l55 76.0 76.0 76.0 76.0 l63 100 100 100 100 fig. 2 luminance 512 512 512 512 768 768 768 768 512 512 512 512 256 256 256 256 192 192 192 192 3 3 3 3 2 2 2 2 1 1 1 1 384 384 384 384 5 5 5 5 4 4 4 4 384 384 384 384 576 576 576 576 www.datasheet.net/ datasheet pdf - http://www..co.kr/
LP133X8-A2M1 liquid crystal display product specification ver 1.0 aug. 01. 2001 page 15 15 15 15 / 24 24 24 24 fig. 3 response time the response time is defined as the following figure and shall be measured by switching the input signal for ?black? and ?white?. tr r tr d 100 90 10 0 % o p tical res p onse w hite black w hite fig. 4 viewing angle = 90 ( 1 2 : 00) yu = 0 z z' yd = 180 (9 : 00) a = 0 (3 : 00) xr = 270 (6 : 00) tft lcd mod u le xl a : eye of observer a : eye of observer a : eye of observer a : eye of observer www.datasheet.net/ datasheet pdf - http://www..co.kr/
LP133X8-A2M1 liquid crystal display product specification ver 1.0 aug. 01. 2001 page 16 16 16 16 / 24 24 24 24 5. mechanical characteristics the contents provide general mechanical characteristics for the model LP133X8-A2M1 lcd. in addition, the figures in the next page are detailed mechanical drawings of the lcd. outside dimensions : horizontal 284 0.5 mm vertical 214.5 0.5 mm depth 5.2 0.3 mm bezel area : horizontal 273.6 0.5 mm vertical 206 0.5 mm active display area : horizontal 270.34 mm vertical 202.77 mm weight (approximate) : 390g (typ.), 400g(max.) surface treatment : hard coating (3h) anti-glare treatment of the front polarizer www.datasheet.net/ datasheet pdf - http://www..co.kr/
LP133X8-A2M1 liquid crystal display product specification ver 1.0 aug. 01. 2001 page 17 17 17 17 / 24 24 24 24 < front view > * unspecified dimensional tolerances are 0.5mm www.datasheet.net/ datasheet pdf - http://www..co.kr/
LP133X8-A2M1 liquid crystal display product specification ver 1.0 aug. 01. 2001 page 18 18 18 18 / 24 24 24 24 < rear view > www.datasheet.net/ datasheet pdf - http://www..co.kr/
LP133X8-A2M1 liquid crystal display product specification ver 1.0 aug. 01. 2001 page 19 19 19 19 / 24 24 24 24 top case (s u s 304) top case (s u s 304) top case (s u s 304) top case (s u s 304) su pp orter main su pp orter main su pp orter main su pp orter main panel panel panel panel bottom cover (s u s 304) bottom cover (s u s 304) bottom cover (s u s 304) bottom cover (s u s 304) www.datasheet.net/ datasheet pdf - http://www..co.kr/
LP133X8-A2M1 liquid crystal display product specification ver 1.0 aug. 01. 2001 page 20 20 20 20 / 24 24 24 24 6. reliability - environment test condition no. test item conditions 1 high temperature storage test ta = 60 c 240h 2 low temperature storage test ta = -20 c 240h 3 high temperature operation test ta = 50 c 50%rh 240h 4 low temperature operation test ta = 0 c 240h 5 vibration test (non-operating) sine wave, 10~500~10hz, 1.5g, 0.37oct/min, 3 axis, 1 hour/axis 6 shock test (non-operating) half sine wave, 180 g, 2ms, one shock of each six faces (i.e. run 180g 2ms for all six faces.) 7 altitude operating storage/shipment 0 - 10,000 feet (3048m) 0 - 40,000 feet (12192m) {result evaluation criteria} there should be no change which might affect the practical display function when the display quality test is conducted under normal operating condition. www.datasheet.net/ datasheet pdf - http://www..co.kr/
LP133X8-A2M1 liquid crystal display product specification ver 1.0 aug. 01. 2001 page 21 21 21 21 / 24 24 24 24 7. international standards 7-1. safety a) ul 1950 third edition, underwriters laboratories, inc. jan. 28, 1995. standard for safety of information technology equipment including electrical business equipment. b) can/csa c22.2 no. 950-95 third edition, canadian standards association, jan. 28, 1995. standard for safety of information technology equipment including electrical business equipment. c) en 60950 : 1992 + a1 : 1993 + a2 : 1993 + a3 : 1995 + a4 : 1997 + a11 : 1997 iec 950 : 1991 + a1 : 1992 + a2 : 1993 + a3 : 1995 + a4 : 1996 european committee for electrotechnical standardization (cenelec) european standard for safety of information technology equipment including electrical business equipment. 7-2. emc a) ansi c63.4 ?methods of measurement of radio-noise emissions from low-voltage electrical and electronic equipment in the range of 9khz to 40ghz.? american national standards institute(ansi),1992. b) c.i.s.p.r ?limits and methods of measurement of radio interference characteristics of information technology equipment.? international special committee on radio interference c) en 55022 ?limits and methods of measurement of radio interference characteristics of information technology equipment.? european committee for electrotechnical standardization (cenelec),1988 www.datasheet.net/ datasheet pdf - http://www..co.kr/
LP133X8-A2M1 liquid crystal display product specification ver 1.0 aug. 01. 2001 page 22 22 22 22 / 24 24 24 24 8. packing 8-1. designation of lot mark a) lot mark a, b ,c : inch code d : year e : month f,g : panel code h : assembly code i,j,k,l,m : serial no. note : 1. year year 97 98 99 2000 2001 2002 2003 2004 2005 2006 2007 mark 7 8 9 0 1 2 3 4 5 6 7 2. month month jan. feb. mar. apr. may. jun. jul. aug. sep. oct. nov. dec. mark 1 2 3 4 5 6 7 8 9 a b c 3. serial no. serial no. 1 ~ 99999 100000 ~ mark 00001 ~ 99999 a0001 ~ a9999, ??.. , z9999 b) location of lot mark serial no. is printed on the label. the label is attached to the backside of the lcd module. this is subject to change without prior notice. 8-2. packing form a) package quantity in one box : 10 pcs b) box size : 371mm x 239mm x 300mm k j i h g f e d c b a l m www.datasheet.net/ datasheet pdf - http://www..co.kr/
LP133X8-A2M1 liquid crystal display product specification ver 1.0 aug. 01. 2001 page 23 23 23 23 / 24 24 24 24 9.precautions please pay attention to the followings when you use this tft lcd module. 9.1 mounting precautions (1) you must mount a module using holes arranged in four corners or four sides. (2) you should consider the mounting structure so that uneven force (ex. twisted stress) is not applied to the module. and the case on which a module is mounted should have sufficient strength so that external force is not transmitted directly to the module. (3) please attach a transparent protective plate to the surface in order to protect the polarizer. transparent protective plate should have sufficient strength in order to resist external force. (4) you should adopt radiation structure to satisfy the temperature specification. (5) acetic acid type and chlorine type materials for the cover case are not desirable because the former generates corrosive gas of attacking the polalizer at high temperature and the latter causes circuit break by electro-chemical reaction. (6) do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than hb pencil lead. and please do not rub with dust clothes with chemical treatment. do not touch the surface of polarizer for bare hand or greasy cloth. (some cosmetics are detrimental to the polarizer.) (7) when the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like chamois soaked with petroleum benzene. normal-hexane is recommended for cleaning the adhesives used to attach front / rear polarizers. do not use acetone, toluene and alcohol because they cause chemical damage to the polarizer. (8) wipe off saliva or water drops as soon as possible. their long time contact with polarizer causes deformations and color fading. (9) do not open the case because inside circuits do not have sufficient strength. 9.2 operating precautions (1) the spike noise causes the mis-operation of circuits. it should be lower than following voltage : v = 200mv (over and under shoot voltage). (2) response time depends on the temperature. (in lower temperature, it becomes longer.) (3) brightness depends on the temperature. (in lower temperature, it becomes lower.) and in lower temperature, response time (required time that brightness is stable after turned on ) becomes longer. (4) be careful for condensation at sudden temperature change. condensation makes damage to polarizer or electrical contacted parts. and after fading condensation, smear or spot will occur. (5) when fixed patterns are displayed for a long time, remnant image is likely to occur. (6) module has high frequency circuits. sufficient suppression to the electromagnetic interference shall be done by system manufacturers. grounding and shielding methods may be important to minimize the interference. www.datasheet.net/ datasheet pdf - http://www..co.kr/
LP133X8-A2M1 liquid crystal display product specification ver 1.0 aug. 01. 2001 page 24 24 24 24 / 24 24 24 24 9.3 electrostatic discharge control since a module is composed of electronic circuits, it is not strong to electrostatic discharge. make certain that treatment persons are connected to ground through wrist band etc . and don?t touch interface pin directly. 9.4 precautions for strong light exposure strong light exposure causes degradation of polarizer and color filter. 9.5 storage when storing modules as spares for a long time, the following precautions are necessary. (1) store them in a dark place. do not expose the module to sunlight or fluorescent light. keep the temperature between 5 c and 35 c at normal humidity. (2) the polarizer surface should not come in contact with any other object. it is recommended that they be stored in the container in which they were shipped. 9.6 handling precautions for protection film (1) when the protection film is peeled off, static electricity is generated between the film and polarizer. this should be peeled off slowly and carefully by people who are electrically grounded and with well ion- blown equipment or in such a condition, etc. (2) the protection film is attached to the polarizer with a small amount of glue. if some stress is applied to rub the protection film against the polarizer during the time you peel off the film, the glue is apt to remain on the polarizer. please carefully peel off the protection film without rubbing it against the polarizer. (3) when the module with protection film attached is stored for a long time, sometimes there remains a very small amount of glue still on the polarizer after the protection film is peeled off. (4) you can remove the glue easily. when the glue remains on the polarizer surface or its vestige is recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane . www.datasheet.net/ datasheet pdf - http://www..co.kr/

▲Up To Search▲

Price & Availability of LP133X8-A2M1

	To Download LP133X8-A2M1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .